Carbon fiber composites · OEM and custom builds
Carbon Fiber Square Tubes
DISLAB supplies carbon fiber square tubes from 3×3 mm to 10×10 mm, in 0.5 m to 1.5 m lengths, with a woven 3K twill surface in gloss or matte. Tubes are cut to length, drilled and machined to drawing, and the wall thickness is confirmed against your specification before production starts.
- 3×3 to 10×10 mm
- 0.5–1.5 m
- Gloss or matte
- Cut and drilled
- From 1 pc
Updated · Reviewed by the DISLAB engineering team
Specifications
The sizes below cover most orders. Anything outside the table is made to drawing, so the dimensions you specify take precedence.
| Material | Carbon fiber reinforcement with epoxy matrix, 3K twill surface |
|---|---|
| Profile | Square outer section with a square hollow bore; other profiles on request |
| Outer size | 3×3, 4×4, 5×5, 6×6, 6.5×6.5, 8×8, 8.5×8.5, 10×10 mm |
| Inner size | 2×2, 3×3, 4×4, 5×5, 6×6, 6.5×6.5, 8×8, 8.5×8.5 mm |
| Wall thickness | Set by the outer size and the load; confirmed on the drawing |
| Standard lengths | 0.5 m, 1 m, 1.2 m, 1.5 m |
| Cut to length | Any length within that range, cut to your drawing |
| Finish | Gloss or matte, with a UV-resistant coating |
| Secondary operations | Drilling, slotting, milling and edge chamfering |
| Density | About 1.55 g/cm³ |
| Minimum order | 1 pc for custom development |
Sending a drawing is faster than describing the part. If you do not have one yet, the outer dimension, wall thickness, length and hole positions are enough for us to quote.
Square or round: which profile fits the job
Most buyers arrive with a square profile already specified, usually because the part has to bolt to something flat. It is worth being clear about what the square section does and does not give you, because the answer is not simply “stiffer”.
What a square profile gives you
Four flat faces make the tube easy to clamp, bolt, bond and datum from. A bolted joint cannot rotate on a flat face the way it can on a curved one, which is why square tube is common in frames, gantries, robot arms and drone airframes where brackets and plates attach along the length. Holes drilled into a flat wall also stay square to the mounting surface.
Where a round tube wins
A closed circular section encloses more area for the same amount of material, and torsional stiffness of a thin-walled closed section scales with the enclosed area. For the same mass, a round tube resists twisting better than a square one. If the load is dominated by torque rather than by mounting geometry, a round profile is the more efficient choice, and we will say so on the review rather than sell you the square section.
| Property | Square tube | Round tube |
|---|---|---|
| Flat mounting faces | Four, along the full length | None; requires saddles or clamps |
| Torsional stiffness at equal mass | Lower | Higher |
| Joint rotation under load | Resisted by the flat faces | Needs a keyed or clamped joint |
| Drilling and fixturing | Simple, square to the face | Curved surface, needs a jig |
| Typical use | Frames, arms, rails, brackets | Shafts, struts, pure torque members |
How the tubes are made
Every tube is produced against a drawing rather than picked from a shelf list. The sequence below is the one used for the square profiles in this range.
-
Drawing review
Outer and inner size, wall, length, hole pattern and the load the part has to carry are checked first. If a requested wall will not close on that size, or a hole lands where the wall is too thin, it is raised before anything is cut.
-
Lay-up on a square mandrel
Woven carbon fabric is laid up around a square steel mandrel, with the number of plies set by the wall thickness the part needs rather than by a stock size.
-
Consolidation and cure
The lay-up is consolidated under pressure and cured on a controlled temperature cycle. This is the step that removes voids and holds the resin content, and therefore the mass, to a predictable figure.
-
Mandrel removal and trimming
The mandrel is drawn out and the tube ends are trimmed square. Wall thickness and outer dimension are checked before the part moves to machining.
-
Machining
Cut to length, then drilled, slotted or milled to the drawing. Hole positions and edge quality are checked against the drawing at this stage.
-
Finish and inspection
Gloss or matte UV-resistant coating, then a final dimensional and visual check before packing. Material certificates are available on request.
Very long, thin sections and heavy hole patterns can make a mandrel lay-up uneconomic. Where that happens we will tell you at quotation rather than after the tooling is made.
Tolerances and inspection
What gets measured, and against what, is the part of a composite order that is easiest to leave vague. For these tubes the checks are:
| Check | Standard | When |
|---|---|---|
| Outer dimension and wall | To drawing | After cure, before machining |
| Straightness | To drawing | Before packing |
| Cut length | To drawing | After cutting |
| Hole position and edge quality | To drawing | After machining |
| Surface and finish | Visual, agreed reference sample | Before packing |
| Documentation | Material certificates on request; packing list and invoice for export | With shipment |
If you need a dimensional report or a first-article inspection with the order, say so at quotation so it can be built into the price and schedule.
Options and customisation
Most orders combine a standard outer size with a custom length and hole pattern. Combinations are quoted individually.
| Feature | Available |
|---|---|
| Outer / inner size | 3×3 to 10×10 mm; other combinations to drawing |
| Length | 0.5–1.5 m standard; cut to any length in that range |
| Finish | Gloss or matte; matte is usual where glare matters |
| Drilling | Hole pattern to drawing, including through both walls |
| Machining | Slots, milled flats, chamfered and radiused ends |
| Wall | Adjusted for the load where the outer size allows it |
Carbon fiber compared with aluminium and steel
The comparison below is about the tube as a structural part. It is not a claim that carbon suits every job; the last row is often what decides it.
| Carbon fiber / epoxy | Aluminium | Steel | |
|---|---|---|---|
| Density | About 1.55 g/cm³ | About 2.7 g/cm³ | About 7.85 g/cm³ |
| Mass at equal section | Reference | About 1.7× heavier | About 5× heavier |
| Stiffness-to-weight | High | Moderate | Lower |
| Corrosion | Does not corrode; needs a sound UV finish | Corrodes without anodising | Corrodes without coating |
| Galvanic coupling | Cathodic; isolate from aluminium and steel | Anodic to carbon; needs a barrier | Anodic to carbon; needs a barrier |
| Repair | Structural damage is not field-repairable | Can be straightened and re-drilled | Can be welded |
| Deciding factor | Weight-critical moving parts | Cost-sensitive frames | High impact and weldability |
Carbon is electrically conductive and cathodic to both aluminium and steel. Where a carbon tube bolts to a metal bracket, the joint needs an isolating layer and, usually, non-metallic fasteners or sleeves; we flag this at drawing review because it is cheaper to design in than to discover in service.
Where these tubes are used
Drone and RC airframes
Arms, booms and frame members where the flat faces take motor mounts and the tube has to stay straight under vibration. The usual demand is stiffness at low mass rather than ultimate strength.
Marine and watersports
Spars, tillers and fittings that see salt water. The composite does not corrode, but the finish has to be intact, and any stainless fastener needs isolation from the carbon.
Medical and orthotic devices
Braces, frames and equipment where low mass and stiffness matter and the tube is often machined after cure to fit an assembly.
Sports equipment
Poles, frames and handles where the square section locates into a moulded or machined socket without a separate key.
Industrial automation
Gantries, robot arms and sensor mounts, where flat faces and repeatable hole positions shorten assembly time more than the weight saving does.
A project example: 2,000 tubes for a drone airframe
One order we delivered was for a European manufacturer of industrial inspection drones. The requirement was 2,000 pieces of 6×6 mm tube with a 4×4 mm bore, 1.2 m long, matte finish, each one drilled to a hole pattern for the motor mounts.
Because the hole pattern was fixed, the wall thickness and drilling sequence were agreed before the first tube was cut, and the matte finish was chosen to keep reflections out of the camera path. The batch shipped in 25 days against the customer’s assembly schedule.
The customer reported the finished frames were about 35% lighter than the aluminium parts they replaced, with stiffness increased by roughly 30% in their bench test. Those figures are the customer’s measurement at acceptance; we quote them as reported, not as a guarantee for a different design.
Frequently asked questions
What sizes of carbon fiber square tube are available?
Outer sizes from 3×3 mm to 10×10 mm, with inner bores from 2×2 mm to 8.5×8.5 mm. Combinations outside that list can be made to drawing, subject to a wall that can actually be closed on that size.
Can the tubes be cut to length and drilled?
Yes. Cutting, drilling, slotting, milling and end chamfering are all done to the drawing, and hole positions are checked after machining. Sending the hole pattern with the order avoids a second operation later.
Is a square tube stiffer than a round tube?
In torsion, no: for the same mass a round closed section resists twisting better. In bending, and in any joint that clamps or bolts to the tube, the flat faces of a square profile usually win. The right answer depends on which load dominates.
Can a carbon tube be bolted directly to aluminium?
It can, but the joint needs isolation. Carbon is cathodic to aluminium, so any moisture at the contact surface drives galvanic corrosion of the metal. A barrier layer plus non-metallic sleeves or washers is the usual fix.
What is the minimum order quantity?
One piece for custom development. Samples are supplied so a specification can be tested before a production run.
How long does production take?
Standard sizes are typically 5–15 days and custom orders 15–30 days. The figure is confirmed in writing with the quotation, because the hole pattern and finish often matter more than the tube itself.
Related: carbon fiber drive shafts · how pultruded profiles are made · composite materials market report
Request a Quote for Carbon Fiber Square Tubes
Tell us your application, dimensions or specifications, quantity, accessory requirements and destination country. Please identify the product in your message.
For drawings or project files, use the email channel on the right.
Get a Fast QuoteCarbon Fiber Square Tubes
Request a Product Quote
Send your drawing, dimensions and quantity. Our team will review the requirements and reply with the next steps.
